Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)


 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
COMPREHENSIVE VIVA ANALOG COMMUNICATIONS
Post: #1

COMPREHENSIVE VIVA ANALOG COMMUNICATIONS


.pdf  COMPREHENSIVE VIVA ANALOG .pdf (Size: 82.96 KB / Downloads: 192)

1. What is the need for modulation?

Ans. Mainly to decrease the antenna size
 to increase the bandwidth of the signal
 to multiplex the signals
 to reduce the interference made when we transmit the signals with nearly same
frequency in the audio frequency range (20-20k)kHz.
 to favour the complexity of the transmission system

2. What is Costas Loop?

Ans. A Costas loop is a phase-locked loop used for carrier phase recovery from suppressed-
carrier modulation signals, such as from double-sideband suppressed carrier signals. The primary
application of Costas loops is in wireless receivers. Its advantage over the PLL-based detectors is
that at small deviations the Costas loop error voltage is sin(2(șiíșf)) vs sin(șiíșf). This translates
to double the sensitivity and also makes the Costas loop uniquely suited for tracking Doppler-
shifted carriers esp. in OFDM and GPS.

3. What is SSB?

Ans. Single-sideband modulation (SSB) is a refinement of amplitude modulation that more
efficiently uses electrical power and bandwidth. It is closely related to vestigial sideband
modulation (VSB)
Amplitude modulation produces a modulated output signal that has twice the bandwidth of the
original baseband signal. Single-sideband modulation avoids this bandwidth doubling, and the
power wasted on a carrier, at the cost of somewhat increased device complexity.

4. What is FM?

Ans. Frequency modulation (FM) conveys information over a carrier wave by varying its
instantaneous frequency. This is in contrast with amplitude modulation, in which the amplitude
of the carrier is varied while its frequency remains constant. In analog applications, the
difference between the instantaneous and the base frequency of the carrier is directly
proportional to the instantaneous value of the input signal amplitude. Digital data can be sent by
shifting the carrier's frequency among a set of discrete values, a technique known as frequency-
shift keying.

5. Noise in Analog communication?

Ans. Analog systems are less tolerant to noise, make good use of bandwidth, and are easy to
manipulate mathematically. However, analog signals require hardware receivers and transmitters
that are designed to perfectly fit the particular transmission. If you are working on a new system,
and you decide to change your analog signal, you need to completely change your transmitters
and receivers.

6. What is a Radio transmitter?

Ans. Radio transmitter is an electronic device which, with the aid of an antenna, produces radio
waves. The transmitter itself generates a radio frequency alternating current, which is applied to
the antenna. When excited by this alternating current, the antenna radiates radio waves. In
addition to their use in broadcasting, transmitters are necessary component parts of many
electronic devices that communicate by radio.

7. What is a Radio receiver?

Ans. A radio receiver is an electronic circuit that receives its input from an antenna, uses
electronic filters to separate a wanted radio signal from all other signals picked up by this
antenna, amplifies it to a level suitable for further processing, and finally converts through
demodulation and decoding the signal into a form usable for the consumer, such as sound,
pictures, digital data, measurement values, navigational positions, etc
Post: #2
please send analog communications comprehensive viva questions
Post: #3
To get full information or details of COMPREHENSIVE VIVA ANALOG COMMUNICATIONS please have a look on the pages

http://projects-seminars.net/Thread-comp...#pid241095

if you again feel trouble on COMPREHENSIVE VIVA ANALOG COMMUNICATIONS please reply in that page and ask specific fields in COMPREHENSIVE VIVA ANALOG COMMUNICATIONS
Post: #4
ANALOG COMMUNICATION VIVA QUESTIONS WITH ANSWER SET-1



Q1. What is amplitude modulation?

Ans: The process of amplitude modulation consists of varying the peak amplitude of a sinusoidal carrier wave in proportion to the instantaneous amplitude of the modulation signal.


Q2. What is modulation?

Ans: Modulation may be defined as the process by which some parameters of a high frequency signal termed as carrier, is varie in accordance with the signal to be transmitted.

Q3. What are the different types of analog modulation?

Ans: 1) Amplitude modulation 2) angle modulation.



Q4. What si the need for modulation?

Ans: Consider, for example, picture signal of a T.V camera. It has frequency spectra of DC to 5.5MHz.such a wide band of frequency can’t be propagated through ionosphere. However, if this signal is modulated with a carrier in VHF and UHF range, the percentage bandwidth becomes very small and the signal become suitable for transmission through atmosphere.


Q5. What are the objectives met by modulation?

Ans: Length of antenna is shortened, signal loss is reduced, ease of radiation, adjustment of bandwidth, shifting signal frequency of the assigned value.


Q6. What are the advantage of PAM and PWM?

Ans: PWM system gives a greater signal to noise ratio as compared to PAM but requires a larger bandwidth to achieve this.


Q7. What is Pulse position modulation?

Ans: Pulse position modulation (PPM) is the process in which the position of a standard pulse is varied as a function of the amplitude of the sampled signal.


Q8. What is the advantage of PPM over PWM and PAM?

Ans: The phase deviation are usually small. The noise produces a smaller disturbing effect on the time position of the modulating pulse train and as a result, PPM waves have a better performance with respect to signal to noise ratio in comparison to PAM and PWM systems.

Q9. What are the applications of pulse position modulation?

Ans: It is primarily useful for optical communication systems, where there tends to be little or no multipath interference. Narrowband RF (Radio frequency) channels with low power and long wavelength (i.e., low frequency) are affected primarily by flat fading, and PPM is better suited.


Q10. What is the purpose of using differential pulse position modulation?

Ans: It is possible to limit the propagation of errors to adjacent symbols, so that an error in measuring the differential delay of one pulse will affect only two symbols, instead of effecting all successive measurements.



Q11. What are the advantage of PPM?

Ans: One of the principle advantages of pulse position modulation is that it is an M-ary modulation technique that can be implemented non-coherently, such that the receiver does not need to use a phase-locked loop (PLL) to track the phase of the carrier. This makes it a suitable candidate for optical communications systems, where coherent phase modulation and detecting are difficult and extremely expensive. The only other common M-ary non-coherent modulation technique is M-ary frequency shift keying, which is the frequency domain dual to PPM.
The other advantages of pulse position modulation are:
• The amplitude is held constant thus less noise interference.
• Signal and noise separation is very easy.
• Due to constant pulse widths and amplitudes, transmission power for each pulse is same.



Q12. What are the application of PPM?

Ans: PPM is employed in narrowband RF channel systems, with the position of each pulse representing the angular position of an analogue control on the transmitter, or possible states of binary switch. The number of pulse per frame gives the number of controllable channels available. The advantage of using PPM for this type of application is that the electronics required to decode the signal are extremely simple, which leads to small, light-weight receiver/decoder units. (Model aircraft require parts that are as lightweight as possible).



Q13. Explain the principle of PPM?

Ans: The amplitude and the width of the pulse is kept constant in this system, while the position of each pulse, in relation to the position of a recurrent reference pulse is varied by each instantaneous sampled value of the modulating wave. This means that the transmitter must send synchronizing pulses to operate timing circuits in the receiver. The PPM has the advantage of requiring constant transmitter power output, but the disadvantage of depending on transmitter-receiver synchronization.



Q14. What is the puprpose of PPM?

Ans: PPM may be used to transmit analog information, such as continuous speech or data.


Q15. What are the analog analogies of PAM, PPM & PWM?

Ans: PAM is similar to AM; PPM and PWM is similar to angle modulation.


Q16. What is Frequency modulation (FM)?

Ans: Frequency modulation is the process of varying the frequency of a carrier wave in proportion to the instantaneous amplitude of the modulating signal without any variation in the amplitude of the carrier wave.

Q17. What is PWM or Pulse length modulation or pilse duration modulation?

Ans: In PWM, the pulse amplitude is kept constant but the leading edge, trailing edge or both may be varied as a function of the amplitude of the sampled signal and care must be taken to ensure that the pulse don’t overlap in a TDM system.

Q18. What are the disadvantages of PWM?

Ans: PWM, in general, requires a greater average power than PAM systems. Also, the PWM system requires a greater bandwidth than PAM.


Q19. Explain the principle of PWM?

Ans: Pulse-width modulation (PWM) of a signal or power source involves the modulation of its duty cycle, to either convey information over a communication channel or control the amount of power sent to a load. PWM uses a square wave whose pulse width is modulated resulting in the variation of the average value of the waveform is directly dependent on the duty cycle D.


Q20. Mention the applications of PWM.

Ans: PWM can be used to reduce the total amount of power delivered to a load without losses normally incurred when a power source is limited by resistive means. This is because the average power delivered is proportional to the modulation duty cycle. With a sufficiently high modulation rate, passive electronic filters can be used to smooth the pulse train and recover an average analog waveform.

Please Use Search http://projects-seminars.net/search.php wisely To Get More Information About A Seminar Or Project Topic
 


[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.
Marked Categories : ac viva bits, viva on analog communications, ac comprehensive viva questions and answers, analogue communication viva questions with answers, analog communication viva questions with answers pdf free download, viva questions for analog communication, analog communication viva questions, viva for analog communication with answer, free download of analog communication viva question and answers, viva asked in analog communication pdf, analog communication viva questions and answers, viva questions of analog communication, ece analog electronics communication viva, www analogcommunicationviva com, analog communications, radio receivers for comprehensive viva,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  viva based question and answers on project diffusion of solid in liquid Guest 1 0 Yesterday 09:21 AM
Last Post: jaseela123
  jntu comprehensive viva questions for ece with answers Guest 1 0 25-03-2017 09:46 AM
Last Post: jaseela123
  comprehensive viva questions for ece free download balu1559 2 544 20-02-2017 11:36 AM
Last Post: jaseela123
  comprehensive viva questions for ece pdf Guest 3 4,342 20-02-2017 11:36 AM
Last Post: jaseela123
  class 12 organic chemistry practical viva questions with answers Guest 2 0 10-02-2017 07:40 PM
Last Post: Guest
Wink cbse class 12 chemistry practical viva question and answers pdf Guest 4 8,505 10-02-2017 04:03 PM
Last Post: jaseela123
  physics viva questions of practicals for class12 Guest 1 0 08-02-2017 10:48 AM
Last Post: jaseela123
  12th physics practical viva question with answer Guest 1 0 07-02-2017 03:46 PM
Last Post: jaseela123
  spm,cc,np comphrehensive viva questions and answers Guest 1 0 04-02-2017 09:36 AM
Last Post: jaseela123
  what are the question ask in viva over transformer project Guest 1 0 02-02-2017 12:58 PM
Last Post: jaseela123
This Page May Contain What is COMPREHENSIVE VIVA ANALOG COMMUNICATIONS And Latest Information/News About COMPREHENSIVE VIVA ANALOG COMMUNICATIONS,If Not ...Use Search to get more info about COMPREHENSIVE VIVA ANALOG COMMUNICATIONS Or Ask Here

Options: